How To Remove A Fireplace Mantel And Surround. Be careful they are heavier than they look. Be sure to work in small sections in order to protect the integrity of the stone wall.
Begin at the top edge and pry the mantel off the side of the fireplace. Begin at the top edge and pry the mantel off the side of the fireplace.
Adding Cement Board To Fireplace Surround Diy Fireplace
Chip off the masonry around stone or brick corbels using a cold chisel and masonry hammer. Cut any caulk using your utility knife (dad suggests this one and i have to admit it’s pretty awesome) carefully carry your mantel to a safe location.
How To Remove A Fireplace Mantel And Surround
How to remove a fireplace mantel.How to remove a granite stone fireplace mantel with a drill, chisel and hammer.However, in some cases, there may be a secondary brace underneath.If it won’t come off, there may be a ledger behind or under it.
If necessary, use the pry bar to create some extra space.Insert a pry bar behind the mantel and pry it off.It can be as simple as a fresh paint job on unfinished or previously painted brick.I’ve explained how to remove a.
Lay a tarp on the ground to help with debris cleanup.Look for connecting screws and remove them from the mantel or ledger using the drill driver.Make sure you are prepared for a huge mess.Measure the height of the room where you’re removing the fireplace so you know how long your sheeting needs to be.
Move over a couple of inches and repeat.Move the pry bar down the side length of the surround;Move the pry bar down the side length of the surround;Or it can be a simple construction project, where you cover up the brick with drywall, wood, or tile.
Place a pry bar along the side of the mantel and tap in place with the hammer if it is a full mantel.Place a pry bar along the side of the mantel and tap in place with the hammer if it is a full mantel.Prep space around fireplace for a huge mess.Push upward on the mantel, rocking it up and down to loosen it.
Put the pry bar just under the front of the top shelf and use the hammer to push the pry bar between the shelf and moulding then pry upwards and repeat pulling the rest off off.Rehabbing your fireplace doesn’t have to mean a major construction project, though.Remove all of the grout.Remove mantel by finding any screws and removing those;
Remove screws from wooden corbels using a drill driver.Remove the corbel braces under the mantel if the mantel has them.Removing any screws or nails will help a fireplace surround or mantel to come away from the wall more easily.Repeat for the other studs across the top of the fireplace surround.
Seal the area around the fireplace with floor to ceiling plastic sheeting.Skip this step for surrounds that are not tile or stone.Slide a utility knife between the back of the surround and the wall.Slide the utility knife around the back of the fireplace to cut through any adhesive or paint.
Slip the flat bar between the top of the fireplace surround and the wall where a stud is located.Subsequently, question is, how much.Tap the pry bar in place and pry the side piece off until you’ve removed the entire piece.Tap the pry bar in place and pry the side piece off until you’ve removed.
The fireplace is often a focal point of the.The ledger is a connecting board screwed or bolted to the wall.The mantel creates an attractive shelf for you to use when displaying your family photos or your favorite artwork.Then, make sure the mantel is cleared off before you get started.
This can be a messy project, so make sure you also cover up any furniture that is in the room as well.This should reveal the lugs holding it to the wall.To start removing one of these fireplace surrounds, you will have to chip away the plaster around the edge of the mantelpiece.Work the pry bar between the edge of the mantel and the drywall, starting at the lowest point, and slowly push the mantel away from the wall.
You can then go about removing the screws, which should start to release the surround from the wall.You can use a rubber mallet or chisel to help pry a fireplace surround or mantel away from the wall if required.You will need a hammer , pry bar, utility knife.